I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Good morning everyone,
I am struggling since a few days to understand how the SPI communication is supposed to work in the SDK 15.0.0....
So far, I am having some issues...
Hi Nordic,
I am using the example in SDK15, ble_central_and_peripheral -> ble_app_interactive. After being connected to a device, and after pairing. I am trying to make...
hi......
i want to sense the temperature and send data to the uart app via ble ... so i want to merge two programs uart and twi sensor
i have tried but it shows error...
Use central-peripheral programs. First advertising and then scan. It was found that during the adveristing the program was running normally, but the adveristing signal could...
Hi:
How to get sine_table[] data,like this.
int16_t sine_table[]= {0,0,23170,23170,32767,32767,23170,0,0,-23170,-23170,-32768,-32768,-23170,-23170};
NRF_I2S->TXD.PTR...
Dear Nordic Team,
Thanks for supporting.
I am working in ble_app_uart_c example in this example is automatically connect with its peripheral. But i need to connect and...
Hi Nordic,
Here is my configuration:
HW: Customize nRF52840
SW: blinky_rtc_FreeRTOS_pca10056
Problem: The led blink for a few sec and the board went into vPortSuppressTicksAndSleep...
I have a nordic nrf52832 dev board acting as peripheral and my client device is huawei honor 9 lite. I'm trying to send two packets (or 45 Bytes data) in one connection interval...
Hi,
I want to know how to send data with 52840Dongle with ble to the mobile, I tried to use the "ble_uart" program of 52840DK, I followed a tutorial, performed a full erase...
Hi,
Is there out of band data available for the Rx path? I want to make sure there is no interference from other bands and if a filter is already implemented in the IC RF...
Dear Team,
I am using NRF52840 for ble_app_beacon and working fine. Now I want to extend the range using 'PHY_CODED' option. Please let me know in this ' ble_app_beacon...
Hi Nordic team,
nRF Mesh is a very good smartphone App for BLE mesh development & Testing. Currently we are running mesh code on one 52DK and use GenericOnOff model to simulate...
Hi. I just started with nRF52840.
When I use J-flash for STM, normally it proveds 'secure chip' as below.
But when I choose nRF52840, I can't see 'secure chip' activated...
Hi. I just started development with nRF52840.
Press "Setting' button, it shows me "The selected device "NRF52840_XXAA" is unknown .......
And actually it doesn't have...
Hi.
I just want to test mergehex. So I put message as below.
mergehex --merge s140_nrf52_6.1.0_softdevice.hex direct_test_mode_pca10056.hex --output out.hex
Both s140_nrf52_6...
