I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hello.
Since i migrated from 1 to 2 SPI bus, IRQ Handler at completion is not called. Can I use 2 easy DMA SPI ?
1 bus was working fine.
here is my config
/* SPI...
Hello Nordevzone:
8.0 multilink example
I tried to use this modified handler to receive notification data from a s110 based application. The centerpiece of the handler...
Hello! I have been playing with this example and got some LEDs blink here and there, but would very much like to have UART working as well. The documentation states that ...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
Hi
I now is developing Android apps on the basis of NRF UART v2.0.
My s110 NRF51 device will switch two modes for differnet 128-bit UUID. These two modes have independent...
The Bluetooth 4.2 specifications allow for an L2CAP MTU size of up to 255 bytes. It looks like the CC2640 already supports the maximum MTU size of 255 bytes with a 248-byte...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
