I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I try to achieve something similar to IBeacon where data is pushed to any device listening, but where the data is changing over time. Is it possible to (frequently) change...
Hello,
I have recently had to install the nrf tools on a mac computer. The tools have been recently ported to macs, but unfortunately I am getting the following message...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
Hello,
I am experiencing some CC register issue in Timer of nRF51822. I am trying to setup TIMER1 for 16 seconds. But I see, that when I try to write to CC registers, the...
The "Intermediate Temperature" characteristic is not coded in the ble_hts.c file.
How could I do to implement this characteristic and maintain the compliance with Nordic...
Hello,
I want to rewritte SEGGER_RTT_vprintf to use sprintf Inside (because it's already linked in my application and allow float display).
The problem is that i don...
Hi
We use the nRF51822 with s110 active. As long the s100 isn't active, we can debug, set breakpoints, stop, continue like it should work.
When activating the s110 and...
Hello,
The question is about CUSTOMER area in UICR. After locking chip wirh UICR.RBPCONF.PALL I noticed that I still able to read UICR.CUSTOMER data.
Could I enable readback...
Hi all,
Google launch uWeave Library project.
uWeave is an implementation of the Weave protocol intended for use on microcontroller based devices.First demo project is using...
