Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
We are looking for an experienced software developer, for existing board with using nRF Connect SDK. We are using nRF52840-dk.
Please, contact me if you are interested.
I have a project using nRF Connect SDK v1.9.1 and recently started having the issue that when I build it in VS Code with the plugin it always asks me to do a Pristine Build...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
Hello, we have a following issue: we would like to use nRF5340 QSPI driver with external RAM to store measurements data. Power supply for PCB is 1,8V, so we tried to use APS6404L...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Hi,
I want to connect LDC2114 to nRF9160. I write the nrf9160dk_nrf9160_ns.overlay and the astri,ldc2114.yaml. I don't know how to set GPIOs in & i2c1 - ldc2114: ldc2114...
Dear,
My customer interesting in nRF52840-DK and would like to know the U2 (IC).
Customer wants the nRF52840-DK board it must be installed IC in the same package (QFP...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello,
Currently, I am working on the nRF 52840 DK and the UART port named uart0 is connected to the on board debugger, Where do i find the pins for the UART1 ? I could...
Can Channel Sounding technology and BLE Mesh be used at the same time? Does the SDK support it? If they can be used at the same time, will it affect the communication of mesh...
I work NCS2.8.0.
In NCS2.6.0, there was no problem if I put the BOARD settings in CMakeLists.txt and ran "west build".
However, in NCS2.8.0, an error occurs. (undefined...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
Hello,
I am looking for information to be able to process CI/CD automatic tests for an nRF5340 project.
I mean compilation of the project, and simple tests by using GitLab...
Hello,
I am using NCS v2.8.0.
In this, when I configured the application to use OOB legacy pairing only mode, the build process failed.
Following is the configuration...
Now I want a packet (8 bytes) to be sent out at 8k, but now it is only about 5k, I did not set the ack, is there a way to verify that the ack reaches 8k,The library currently...
