I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
I am planning to use the balun BD2425P50100AHF with the nRF52833. The voltage on the pins BAL1 and BAL2 can go up to 15V.
I am wondering what is the maximum allowed...
Hi,
We have developed an application in central mode using BLE nRF52833 chip running on SoftDevice140 , Version 7.2.0
We now need to add support for FEM nRF21540 ...
Hi,
I am using NRF52840 development kit and I need to modify the PCNF0 register values for our application.
I am developing our application using the sample application...
I have ran the Mesh light demo successfully, and capture the Bluetooth HCI log (*cfa file) from my Android phone.
However，the transaction between my phone and the nRF52840...
Hi everyone,
Not very sure this is the right place to share this, if not, moderator please help me to move it to where it should be.
I just want to share with you a...
Hi, i have two nRF5340 DK that i'm testing with the Thread CoAP client/server samples.
I found out that with the newer DK, both the clinet and server samples work. With...
HI,
I keep working on my new customize board with nrf52833 SoC and now I want to add e-paper screen. There is any examples about adding a e-paper screen to customized board...
I am a beginner for ARM microcontroller, I am unable to generate the PWM wave and ADC simultaneously in the nRF51822, but both the things happening separately. I need the...
Hello,
I'm trying to understand if I can use BLE GATT Queue in my peripheral for sending Notifications. All the example and documentation about BLE GATT Queue seem to be...
Hi
When I build mesh bootloader code, there shows flash size not enough,
Could you tell me wher I can change the size, please?
c:/progra~2/gnutoo~1/62017-~1/bin/....
Hi,
I wanted to setup a network connectivity to nRF5340DK to send RPC messages to remote server(Blockchain Network).
Already I tried to setup OTBR using RPi and nRF52840...
Hi,
We are using NRF52832 as our main processor along with an IMU sensor and a vibration motor. We are wondering if using system on mode as power off state (instead of system...
Greetings,
We are using the NCS for the development of a new product with a custom board based on the nRF52840 MCU.
First, we would like to use the Serial DFU feature...
Hi Nordic community,
I'm trying to generate a 1 MHz base clock with one of the peripheral timer, and in the timer ISR does some GPIO toggling.
I followed the nRF5 SDK...
Hello dear Nordic team,
I'm quite experienced in developing under SDK V15 and V17 but absolutely novice for nRF Connect SDK so my question may seem ridiculos. Hope someone...
