SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hello all, We 're working on our custom PCB prototype. We can see current consumption according to this profile even though the flash memory was erased. Also the modem FW...
Hello all,
I have started to port the code from the nRF52dk in Segger EM, indeed, everything so far works on the NRF52 dk , so I have opened the Blinky example for the nRF52820...
Hi,
I am using an nrf52 DK and facing an issue regarding the GPIO voltage levels. The GPIO voltage is around ~2.35V when its in LOW state and slightly increases when in...
Hi,
like mentioned in the caption, i have updated the nRF Connect SDK version from 2.0.0 to 2.0.2 and noticed, that the debugging does not longer work as expected and before...
Hello, I plugged in the nRF52840 dk and LED1 fades in and out. It does not blink. I am unable to connect to my phone. I tried to drag and drop some hex files to the JLINK...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
Dear Community, Following the Nordic's sample of the (<ncs root>/nrf/sample/caf) the LED module & (CAF) Button module demonstrate the LED states & LED effects (awesome!) After...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example and faced some troubles.
I'm following this guide https://infocenter...
I want to use the BLE Secure connection feature with the following options
CONFIG_BT_SMP_SC_PAIR_ONLY=y
CONFIG_BT_SMP_SC_ONLY=y
CONFIG_BT_SMP_APP_PAIRING_ACCEPT=y
CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY...
Hi
I'm working with a PDM mic for nRF52832 SDK v17.1 on a project and I have a questions about PDM driver working.
Whats the difference between the buffer pointer in nrfx_pdm_buffer_set...
Hi Team
In thingy91---hardware-files-1_6_0.zip, the QM12038 is end of life status now. So do we have any new design to replaced it? Thank you.
www.qorvo.com/.../QM12038...
I just finished the second prototype of a nRF9160 board. First one worked flawlessly, but had poor GPS reception. Rewamped the matching and added SAW filters.
However, now...
I have to switch between several different scanning modes.
I scan in passive mode to get all sensors' advertisements (no connection).
I scan in active mode to get a specific...
Hi everyone
I want use the pwm_driver example of the SDK download at nRF52833 DK
However, some problems were encountered after the migration
I replace the preprocessor...
