SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
Hello!
I am working on a medical device project utilizing nrf52832 microcontroller. We use a mobile app to control and interact with the device through BLE since the device...
Basic Bluetooth connection question
How do advertisements usually work? So I have earbuds and a phone. When I pull the earbuds out of the case they auto connect to a bonded...
Hi All!
I am using nrf52820/33 and am able to successfully connectable advertise (coded PHY) by nrf5 SDK. Now I want to use NCS (Zephyr RTOS) to do the same job . Can...
Hi! I'm trying to use the nRF Connect App on a M1 Mac. I keep getting the error shown above with my Jlink connected.
This is the output of the nrfjprog cli tool:
How can...
Hello,
I have been experimenting with the direction_finding_peripheral sample in the nRF Connect SDK. I have been trying to connect to the peripheral using a custom device...
Hi, I'm working with nRF52832 and S132 v6.1.1 on SDK15.3.0. I'm using two nRF52832: one is scanning (active scanning) and one is advertising, and I want to exchange data between...
Hello everyone,
I am developing an application, with the nRF52840 chip (actually BMD-380 ) , that streams via BLE data read by an SPI sensor (ADS1293) to an Ubuntu machine...
I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned.
I want to know...
We have a requirement of sending data to nrf mesh app without provisioning. So Can we use health server model to send data on app without provisioning?
The reason we choose...
My understanding is that the Modem Library is a dedicated interface to the internal modem in the nRF9160.
We also need a 2nd modem interface to an external device that also...
Hi
We are developing a system based on nrf desktop application of nRF Connect SDK 1.90. There are 4 devices in this system: a dongle, a central device and two peripheral...
