Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Is it possible to install the development environment on a PC that is not connected to the internet.
I need to be able to download all the files from a PC connected to the...
Hello.
I need to add an output gpio to the dts file, I modified the board.dts file, inserting these lines in the leds section
res: res_ {
gpios = <& gpio0 17 GPIO_ACTIVE_LOW...
To flash a new firmware I always do the same thing.
Open NRF Connect
Open Bluetooth Low Energy
Click: Start Scanning
Click: Sort by signal strength
Choose the...
Hi,
As well know, nRF52832 have more then one SPI and TWI interface.
How can I use SPI and TWI interface in the same program? for example, use SPI-0 and TWI-1.
Thank...
I don't understand how the guide gets to the Open IDE button. I used the automated installer and it did not appear for me. The guide did not provide any instructions on how...
I see that in the 6.20.14.20 RXADDRESSES in Reference Manual I can enable multiple addresses in the same time, so is it possible for nrf52840 to listen on several addresses...
SENT protocol uses a 1-wire interface to transfer data using time intervals. To receive data you simply measure the time between pulses on the wire. The transmitter never...
When I use the BLE mouse example in the nRF5 SDK (17.0.2), it works on iOS (14). However, the report is divided into 3 parts. I would like to combine the mouse buttons, X...
We are developing a controller for an Electric vehicle charging station. Already developed and successfully running the firmware on ESP32 for which we had used platformio...
I am using this tutorial to write a custom service and I got to a point to add custom characteristics and got a few questions:
- I don't seem to find any characteristic...
nRF52832 nRF5 SDK V17.0.2 SoftDevice S132 V7.2.0
I am running the sample program ble_app_uart in the above environment, but sometimes I miss UART received data. Teraterm...
Hi,
I want to do a custom developpement (custom board) for my project.
I have copied to a folder on drive D/: the peripherial_uart sample, as well as the folder Board...
Hi
We are trying to configure Nordic UE (NRF9160) at our local setup. In order to flash software we performed following steps:
We used ' carrier_deploy_e7f4d5d4-f607...
Hi,
I am looking to design a nRF52833-CJAA (WCSP/ BGA package) board using 4-layer stack.
a) do you see any issue in doing that, vs. 6-layer stack used in nRF52833-DK...
Hey
We encounter problems with the modem not establishing a connection after rebooting the processor for a few times.
Issue:
Firmware is booting normally
Cellular...
