Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Dear Sirs,
I am trying to use the FDS Storage Library to store 4word = 16 bytes in to flash.. Which seems to be working fine. No errors and the function is shown below...
Hi,
We have custom board based on nRF52833 SoC. We are trying to use SDK_v16.0.0/examples/ble_peripheral/ble_app_uart/pca10100/s140.
Using Segger Embedded studio, program...
I'm planning not to have a device name UUID in the advertisement packet, instead set scan filter based on manufacturer-specific data. Is this possible in SDK16? If so please...
Hi, is there any public repository in which I could track changes in zb_cli_wrapper library? I had problems migrating from 0.2 to 0.3, and don't want to do this another time...
Hi!
Since I do not have a SIM card that provides support PSM or eRDX I need to switch the system mode manually.
In my config I have CONFIG_LTE_NETWORK_MODE_LTE_M=y ...
I generated boot-loader (logging disabled) from SDK 12.1.0 for adding a signature check during DFU for nRF51
The problem I am facing is with the size of bootloader (hex...
Hi I checked the relevant topics in the forum but none of them fixed my issue so I just create a new one here.
Basic info:
Hardware: nRF52 DK PCA10040
SDK: nRF5_SDK_15...
Hi,
I'm having issue connecting to the nRF52840_DK through J-Link and nrfjprog. I was able to connect to it the first time and upload simple BLE sample, but afterwards I...
Hello,
I'm developing an app for nRF Connect Desktop based on the nRF Connect Desktop BLE App.
I would like to find a characteristic item based on an UUID. Where is the...
How is it with SUPL and NB-IoT, will it work? AFAICS, in the example code, the supl_support code only uses TCP, and this is not a protocol supported when the device is using...
<Environment> - Windows10 - nrf v1.3.0 - modem fw 1.2.0
I'm attempting to make a socket and communicate with the modem using it.
However, sending data doesn't work out...
Hi everyone,
Looking the nRF52840 Product Specification v1.1, I see that there are several System Off modes.
1. Using the function sd_power_system_off() what is the by...
Hi,
i'm new on using nRF5 modules and i have some question about how to program the nRF52840 on a custom board, so with a completely new chip.
Reading the schematic of...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
