Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi there,
We are currently running tests on the nrf9160 DK using an iBasis SIM card, which should be capable of connecting to multiple networks. We are trying to understand...
Hi,
How is the LTE-M or NB-IOT network availability for very much remote locations like forest or mountains for emergency use cases compared to low-earth orbit satellite...
NCS ver: 2.0.1
chip: nrf52840
node: MTD not SED
network: one OTBR as leader and one MTD as child
After about 4~10 hours, MTD will offline. Sometimes it can reconnect...
I like to enable compiling my code with c11 or c17 but when compiling with west this does not seem to be possible.
To force the compiler to use c11, I used option:
CONFIG_COMPILER_OPT...
Hello,
I am experiencing a SoftDevice Controller ASSERT: 62, 1846. I am using a nrf52832 acting as a peripheral and nRF Connect SDK v1.9.1. This assert happens when large...
BLE-app-blinky client not working
BLE-app-blinky sample build success, LED1 on, when connect LED2 on, but i can not see client service uuid in my android app.
i cannot...
Hi there,
We are doing some testing on an eSIM with the nrf9160 DK, and we are looking for an AT command that can be used to read the eUICC ID of the SIM. We are using the...
Hello,
We are planning to integrate the LwM2M carrier library. Our system uses mfw 1.3.3 and NCS 2.1.0.
Based on the following page https://infocenter.nordicsemi.com/index...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
This is a follow-up to my previous post . I'm developing a BLE Peripheral application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice...
I think this is a bug report for the VScode plugin
One of my boards shows this error when I try to debug
Nrf52833 custom board connected with SWD on Jlink
I was...
Hey there ,
I am trying to modify the Nordic Radio Test example from the pack installer in Keil
for some reason I am getting "
Resource Not Found
We're sorry,...
