Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I am working on NRF52840, I want to read ADC data over I2C communication. Can you please tell me how to implement the code in nrf52840.
Thanks & I am waiting for your...
Hi,
Our device nRF 52832 using connect SDK connects with the Android application. And successfully negotiates an MTU size of 247.
Is there any call back in the nRF SDK...
Hi!
I have three new nrf52840 dongles and I am not able to provision any of them. I load the code nrf/bluetooth/mesh/light (SDK v2.1.0) in one of them for the first time...
I am using the nrf52833 dk board with vs code , I have tried all the solutions that I could find on the already available asked questions, example https://devzone.nordicsemi...
SDK: nRF5 SDK v17.0.2
use example SDK17\examples\ble_peripheral\ble_app_uart to add DFU over BLE
SoftDevice: ANT_s332_nrf52_7.0.1.hex
MCU: nRF 52832
windows application...
Hello, guys.
I just wondered why use LTE Link monitor from nRF Connect make nRF9160 scan lte-m networks and even connects to it.
And when I'm trying to use external MCU...
Hello,
We are using this module in our new product and are in the process of Bluetooth certification. The BMD-350-a-r lists QDID of 101018, but the nRF52 family lists...
Hi,
We are using nrf5340 and nrf connect SDK V2.0.0
Using below code, we are able to scale up/down the processor frequency.
However, in our application we want to...
Hello,
I want to specific a hci event in zephyr RTOS when using nrf connect sdk. But I don't know how to achieve it.
In Bluetooth Core v5.2, vendor specific events have...
Hello,
I would like to create my beacon application to publish periodically (e.g. 10sec) data related to three temperature sensor.
What're the possible solution to implement...
Hi Team,
I am using nRF5340 dev kit and NCS(Nordic connect SDK 2.0.2)for my DFU POC purpose. I want to perform DFU update of nRF5340 through nRF USB port instead of the...
Hi developers,
Now, I want to get a correct Tx power value. I printed out the value from "ble_gap_evt_t->params.adv_report.tx_power" and could get only 127, even this...
Hi,
I am using 5340 but it's uart consumes a lot of power 2.01mA
SDK: NCS2.1.0
project: peripheral_uart
I have disabled all other peripheral equipment,put all...
when I open nrf connect for desktop i got blank page,
and there nothing in the console:
I've installed/am using:
nRF Connect for Desktop v.3.11.1
J-Link V7.68b...
