Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I have an application where I need multiple AWS_IOT_SEC_TAG to connect to different AWS IoT servers, including the nRF Cloud server. How can I do that with the CONFIG_AWS_IOT_SEC_TAG...
Hi all
Im trying to implement on bluetooth communication between two nrf52840 DK, I have made a custom uuid service on peripherial. Now I have to do GATT discovery service...
Hello! We are developing a schematic for our device and trying to correctly assign GPIOs for different peripherals. There is the Cross power-domain use section in the documentation...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hello,
I am developing on the NRF54L15 DK board, using the SDK v3.1.0 and v3.1.0 toolchain. I am trying to use the macro NRF_RADIO_INT_RSSIEND_MASK, but RADIO_INTENSET_RSSIEND_Msk...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
HI，
I am using the nRF54L15 with SDK v3.0.0. I am currently using Timer20 for a counting function. My original power consumption was 4.6 μA when Timer20 was not enabled...
Dear Nordic DevZone,
I have a question which is quite noobish but I want to make sure I am using the right tools for the job. My setup looks like this I have a raspberry...
After gradually increasing up to ncs 3.1.0, the following issue occured: After:
LOG_INF ( "Initializing modem library" );
err = nrf_modem_lib_init ();
if ( err ) ...
Hi,
I’m working on the T5838 Invensense PDM driver for the nRF54L15 .
I’m referencing this driver: IRNAS T5838 Driver , and have updated it to work for SDK 3.0.2 (including...
Hi [Nordic Support Team / Developer Team],
I would like to confirm why the nRF54L15DK is not listed among the supported development kits for the Bluetooth: Peripheral ANCS...
