I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I read this post https://devzone.nordicsemi.com/f/nordic-q-a/10668/rssi-without-connection
I want to know how large the RSSI value will affect the connection. Is there a...
Hi,
I am developing firmware for NRF52811, using SDK 17.1.0 and Soft Device S112.
I need to write a characteristic longer than 20 bytes. I thought it could be done with...
The bluetooth connection is automatically disconnected, and the reason is 0x3E. Is this related to the small RSSI value? I set the transmitting power as 4DB, and the RSSI...
Hello,
I'm exploring the nrf5340 controller with a Fanstel evaluation board (EV-BT40) I use the SDK V1.7.1 with vsCode.
Used example "Bluetooth: Peripheral LBS".
Connecting...
I've recently flashed USB CDC ACM example to NRF52833. Even though everything seems to be working, there is no COM port listed on Windows. I've also tried Zephyr's USB CDC...
I got 2 NRF52840-DK Development Kit recently. But for one of the boards, the programmer firmeware encountered timeout during upgrade. The other board did not encounter this...
Hello All,
I am using nRF52840 Dev-kit and SDK 4.0 for Zigbee and thread. Due to some functions, we are using SDK 4.0 for this project which is not present in SDK 4.1. ...
Hello
In my another ticket https://devzone.nordicsemi.com/f/nordic-q-a/81555/ncs-upgradable-bootloader .
I know there is currently no support for upgrading the bootloader...
Hello,
I build my project with “Visual Studio Code” and with “SEGGER Embedded Studio”. There are some warnings when I use VS Code. When I use SEGGER to build the code...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1
I have below structure to frame the data packet and i need to send this packet to another thread through MailBox...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
We're working on an nRF52840-based project that started development on SDK 17.0.0 and Softdevice S140 7.0.1, but we wanted to get it to the latest release before production...
Hello,
I am working on Arduino's platform and decided to ditch the ArduinoBLE.h library due to its overhead.
I would like to send high frequency (2Mbps per the spec ,...
Hi,
I've trying to get the Omnivision OV7670 to work with the nRF52840-DK. I'm not completely sure whether I've configured it correctly. My pin assignments are adapted from...
