When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
I am using the nfc_writable_ndef_msg example in the SDK to write from my phone to the board using NFC. I get it working successfully however, I am also trying to add code...
Hello, I'm using nRF52833, pca10100, s140.
I'm going to write a code using the external 32.768khz crystal to determine if the port is high/low every 0.5 seconds through...
During the release, we got 2 files with firmware, with and without confirmed in the name.
I want to upgrade my device with the nRF Connect application and confirmed firmware...
Hi all：
We update SDK from 11.0.0 Version to 17.0.2, the hardware is same, but from 17.0.2 package, we run DTM in single channel mode ,data lost is 40%. DTM from 11.0.0...
I have an issue with creating a Bluetooth mesh gateway. It would be better to use nRF Connect SDK for me, but nRF5 for Mesh is also fine. As I've found among answers, not...
Hello guys,
I try to implement a pdm sensor on the nrf 52 dk which sends the audio data to a central device.
My setup is two nrf 52 dk one acting with the modified ble...
Hi,
I am developing application in nRF_connect_SDK v 1.4.2.
I have a problem in Debug the code 1. When i debug the code the breakpoints is not appearing
2. When i...
Hi Nordic,
how do i interpret properly return errors? I l know that it depends on the base address but sometimes it does not correlate at all.
For example, currently...
