Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi! I am trying to write code on MFRC522 to read data from RFID tags and write data to them, but the datasheet leaves much to be desired, and libraries are available only...
Hi,
I want to upgrate bootloader in my firmware.
IC: nRF52832
SDK: 17.02
I have finished my project, this project include boot + softdevice + app + settings,and...
Hello support team Devzone.
I am new member and i have a nRF51 DK board.
I try to create hex file for my nRF 51 DK board on the website : Mbed Compiler
when compiler...
Hello,
I'm sorry for this question, it can be easy for most of you I guess. I would like to measure the current consumption of the Thingy91, I see in the documentation...
I am running a simple cloud example where I am trying to send a CoAP GET message to coap.me:5683 server over Thread.
I can ping 64:ff9b::0808:0808 and get a response. I...
Hello I want to know what is the command that I must add to the ble_uart code which exists in the SDK library to send hello word using the bleutooth in the nrf UART application...
in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_uart,data number is limited 20 bytes, more than 20bytes BLE will part data in two or more packs to send or receive...
Hello everyone.
I'm trying to run examples provided in Zigbee v4.1 https://www.nordicsemi.com/-/media/Software-and-other-downloads/SDKs/nRF5-SDK-for-Thread/nRF5-SDK-for...
Hi,
https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs , I have used this link to access the nrf sniffer hex...
I'm struggling to understand the difference between nrf_pwr_mgmt_run() and sd_app_evt_wait(). When should I use each one? It looks like nrf_pwr_mgmt_run() calls sd_app_evt_wait...
ok I am using nrf52820 and sdk nRF5_SDK_17.0.2_d674dde
when i was using
ble_app_uart\pca10100e\s112
Its work correctly
and
the dfu
pca10100e_s112_ble
also...
I am having problems advertising both FOTA and a custom service. I started with the peripheral sample (zephyr\samples\bluetooth\peripheral) and the smp_svr sample (\zephyr...
A SoftDevice is software which implements a wireless protocol and the nRF51 and nRF52 series specifically mention them. Since the nRF5340 has a dedicated network processor...
Hello,
I'm coming to you with a beginner question, I would like to use the functions localtime, difftime, strftime but I saw that time.h is not included. Is it possible...
The test of I2C signal found that the logic low level could not be lowered. It was pulled up to 3.3V through the external 1K resistor, and the logic low level of I2C was about...
