Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello,
I need to measure current consumption on the nRF52805 in sleep, TX, and RX modes. Which sample applications are recommended for each of these measurements? Additionally...
Hello,
I am facing issue in reading the eDRX mode configurations using AT Commands on nRF9160. Below are the details of hardware & modem fw version.
1. Modem FW version...
What is the recommended way to clear the retained LATCH register using the zephyr generic GPIO functions after waking on interrupt from system OFF? It does not appear to be...
I have designed a custom PCB using nRF54L15 SoC and have gotten it verified from Nordic people. I will share the gerber here as well. I am using VS Code for flashing the code...
# Console disabled - uart30 used exclusively for MCUmgr SMP
CONFIG_SERIAL = y
CONFIG_CONSOLE = y
CONFIG_UART_CONSOLE = y
CONFIG_PRINTK = y
CONFIG_LOG = y
CONFIG_MAIN_STACK_SIZE...
Hi everyone i have a problem with building a project, i dont know what i did wrong, before everything was building fine, but now if i pristine build any project some lines...
Hello,
My application crashes with a Kernel Panic (ZEPHYR FATAL ERROR 4) during NFC communication :
ASSERTION FAIL [ header.ctx_size <= 16 ] @ WEST_TOPDIR/nrf/subsys...
Hello this is my first time designing nrf series. and i want some feedback of my board design and rf circuit
Thanks in advance for your time and suggestions.
these are...
Hello,
I purchased my first nordic semiconductors device, the PPKII, from Farnell.
I just received it today and installed the required software (nRF Connect on macOS...
Hello, I'm using Fanstel's BT840X that includes a SKY66112 front end. It works great with the FEM module in NRF Connect SDK. My problem is that my device has the option to...
We are using nRF54L15 with Zephyr + (NCS) for a low-power application.
Our firmware performs the following cycle repeatedly:
Wake up from System OFF
Perform...
Hi,
We found a weird case that when we re-populate the definition of SPI-NOR flash
- From original pin (gpio0.8/9/10, U15 populated on NRF7002DK)
- To pins (gpio1...
Hello Nordic Team,
I am implementing OTA in a pairing and bonding-enabled application, but I am facing an issue during the ZIP file upload. Additionally, the graph is...
Hello,
I'm working with the nRF9151, and I want to get useful information when a NULL pointer dereference happens, as I am used to on other devices. However, when a NULL...
