Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
While collecting 2-byte samples via SPI4 (with a 32 MHz clock) using PPI and timers—one triggering transfers at 400 kHz and another handling an interrupt every 512 samples...
Hi, Im setting up a project for custom board based on NRF54L15. I followed a tutorial on creating custom board and it works fine. Now i want to add BLE functionality similiar...
Hello, Nordic team.
We are getting the following error and log when we try to program our new nRF52840 DK on Windows 10:
Failed "reading readback protection status...
I am attempting to increase the MTU size on s132 3.0.0 and need to increase the available SoftDevice RAM unproportionally.
For every MTU byte I need to give dozens of bytes...
my minimal main() does the following, after coming out of reset with the MCU in its default state:
NRF_P1_S->DIRSET = 1; // LED0 output NRF_P1_S->OUTSET = 1l // LED0 on...
Hi Support Team,
I want to use an external flash(2M byte) to store the sensor data in a 'circular overwrite' way. I now tried it with the FCB(Flash Circular Buffer) on nRF5340...
I am currently reviewing Zigbee for an upcoming project using the nRF5340DK board. The build environment is nRF Connect for VS Code Extension Pack, and I’m using SDK version...
Hello,
I've developed a PCB that connects an RTD (PT100) to a Wheatstone bridge, set to 100 ohms at 0°C. The bridge terminals (as seen in the diagram) connect to AIN4 and...
Hi everyone,
I am experiencing an issue with my custom board configuration for the nRF9151. When using the same code that works with the nRF9151 DK configuration, I encounter...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
I am using VSCode with the nRF Connect extension (latest) and SDK 2.9.1.
I made my new app from the Bluetooth Peripheral sample.
When I try to debug I get the following...
I am using VSCode with nRF Connect extension with the 2.9.1 SDK.
I am trying to write my own device driver for the Zephyr OS and the TI CC1101 chip. Since the tutorial isn...
Hi,
nRF52832, SDK 17.1.0 with Softdevice S132.
Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
Hello,
I use a PKK2 for power measurements on a nRF9160DK and Feather nRF9160 from circuit dojo. With the UDP example to test it out the sleep current so I can determine...
Hi Sigurd,
I'm finally using the mcuboot and mcumgr_cli I worked on in summer of 2023. I generated the mcumgr_cli for debian with go lang back then. I'm building my app...
