I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
Dear Support / forum,
After reading the user and API guides, browsing other posts, and playing around with the ack-payload example, I think I now have a pretty good understanding...
Hi,
I am having a issue with building an application in IDE for nRF9160
Application : Asset tracker
I have been able to build this "problemfree" before, but this morning...
Hi~
I am developing door sensor system using nRF52840.
Currently for power consumption, sensor (nRF52840) is system off(NRF_POWER->SYSTEMOFF=1).
nRF52840 can wake up...
Hi, I have 8 peripheral devices each one has at least one sensor attached to it( peripheral will be nRF52xx), the sensor has a sampling period of 8ms. I will be using android...
Hi,
In BLE mesh v3.1.0 I see a file debug_pins.h. For what these debug pins are used and can I disable it for my custom board?
And one more thing related to PA and LNA...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
