Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
let say i have a temperature sensor connected to one nrf 52840 dongle of a mesh network. Now can i make the Led of all the dongles glow if the temperature increases the given...
I downloaded the latest nRF5_SDK_15.3.0_59ac345 and some other old versions of SDK documents. (I am trying to use pca10040 development kit to program Fanstel EV-BT840F, aka...
Hi
One of our customers have complained, that our sensors are making occasional errors.
I have looked at it, and they are correct. About 1 in 8 Million packets send...
Hi, I have my custom board for the nrf9160 ,
I was able to program it through the built in programmer of the nrf9160 dk but I have an issue, when I connect the VDD to the...
I'm using adafruit_tag_reader example to read ISO14443 tag. When I put a tag near scanning area of PN532. It reads tag multiple times till I remove that tag from there.
...
Hi!
I am using IAR compiler for my project
I declare global variable
__no_init u32 uPowernResetSignature;
in my code I assign value to this variable
uPowernResetSignature...
Thank you for taking time to look at my problem!
I have managed to combine the TDK/Invensense library for their IMU MPU9250 within the SDK 15 utilizing simple TWI calls...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi, I am trying to modify UICR PSELRESET but its not changing. Any help?
NRF_UICR->PSELRESET[0] = 0xFFFFFFFF ; NRF_UICR->PSELRESET[1] = 0xFFFFFFFF ;
Thanks
Hi,
I'm developing an application using the timeslot API for a custom radio protocol. The application also uses a number of the nRF52832 peripherals, as well as the app_scheduler...
Hello,
I'm having an issue with scripting AT comands directly into the code of the nRF9160. I'm a novice at all this so I apologise if the mistake is an obvious one.
Inside...
I get "ERROR: There is no debugger connected to the PC with the given serial number." when I run e.g. nrfjprog --eraseall on command line.
Programming/debugging using VisualGDB...
Hi,
The User Guide v1.3 in Chapter 2 (minimum requirements) states "SEGGER J-Link Software" under "Software requirements". Is there J-Link software specifically for use...
I've been developing firmware for the nrf52840 for a few months using armgcc+openocd+arm-none-eabi-gcc working successfully. I recently upgraded my ubuntu version (18.04)...
