Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi there,
I am trying to automate the ADC sampling in a regular way.
Application timers seem to be a bit irregular if I depend on not loosing too many miliseconds on each...
Hi,
I tried looking over the docs but I could not find anything specific to my question, which bytes in the NRF_FICR->INFO.VARIANT contain the hardware version ID? e.g....
Hi
I am using nrf52840 Ble_App_Beacon() for advertising Beacon. so, i want to consume my power more down for battery life.I expect the nrf to go to sleep mode after advertising...
Hi
Could nRF52840 - USB Audio run on Android system?
We tested it on Samsung and ASUS Android phone then got it fail.
Please give me a comment.
Thanks.
BR
Atl...
I wrote a code using ble_app_uart peripheral example of sdk 11 for nordic nrf52832 development board.
We are making our custom boards where we are using Rigado BMD-300,...
I am trying to set the Memory protection bit and PinReset configuration with OpenOCD. I have applied the NRF52 patch (outlined here: devzone.nordicsemi.com/.../ )
I am...
Hi
I wrote the SoftDevice(s132_nrf52_6_1_0_softdevice.hex) with nRF go in the following procedure.
Erase terget.
Writting the SD
In the Log area, it is indicated...
Hello,
I have just got a brand new PPK board, and would like to use it with an external J-Link. As far as I could tell by reading the documentation , this scenario is not...
I am working on the nRF52840 DK and nRF52 SDK 15.2.
I can run the USB CDC ACM example and the USB Audio example successfully.
Is there a way to create BOTH devices at...
My code compiles and runs fine in debug mode with logging turned on.
In Release mode, it builds and runs fine with logging turned off, but if I turn logging on (i had an...
Hello,
I want to create an application for the nRF52832 using Segger Embedded Studio and the nRF-SDK. In order to have a clean and portable solution I would like to have...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
Hi everyone,
I have been looking for information about this, but I have not been able to find anything. I would like to send data employing UART, but I can not use the...
