Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello,
I have some problem on my mesh application. (similar application as simple-onoff model)
Sometimes, the server(sensor) devices fail to transmit packet while receiving...
Hello Nordic Community, this is my first post, although I've been using the forums extensively for development.
I've been working with ESB on the nrf52832. The protocol...
I'm playing around with the light and switch examples with the Bluetooth mesh SDK on nRF52832 devices. I'm trying to find out what the maximum distance would be given changes...
Hello, I'm new to this devices. I have several NRF52840 devices and i want to connect them to a Raspberry PI via BLE. I'm not using sensors yet, I just wanna establish a simple...
Hi,
I use nRF5 SDK v15.0.0. In my application I need to change Bluetooth identity address. I can not use BLE_GAP_ADDR_TYPE_RANDOM_STATIC address type, because I need to...
Hi,
I have migrated my projekt from SDK 14.2 to 15.2, the bootloader is basically the secure_bootloader example with some tiny adjustments. When I try to upgrade my product...
Hi all,
I encountered problems porting MbedOS based software which uses Bluetooth Low Energy from MbedOS 5.10 to 5.11 to use the extended features od BLE 5.0.
The ble...
I have interfaced two Nordic nRF52840 boards with one as master an other as slave .
In the image attached signals from down depicts Salve seelct,SCLk MOSI and MISO of Master...
I run into problem, I think for now resolved, but questions remain: Do I have to stop BLE whenever changing ADC config? What did not work?
I don't know why it does not...
Hi, we made a custom board with nrf52832 and flashed example code experimental_ble_app_blinky from sdk13.
We are trying to change the radio txpower other than 0db (default...
Hi all,
I have a nRF52840 development kit and flashed (I believed it flashed successfully) with direct test mode .hex file from SDK 15.2. What I facing was not able to run...
NRF52840 - SDK 15.0 + Some register based custom functions. S140, 6.0.0. In order to work around some of the hardware limitations with SPIM in the context of a project, we...
The PWM Driver has all sorts of fancy stuff for dealing with clever sequences - but I can't see anything to just set a simple, steady, fixed duty cycle!
How does one just...
I need to configure 2 devices as relay nodes in order to relay messages from the client node to the server node
How can i implement this in the light switch example ?
