Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
The example projects I am referring to is located here:
nRF5_SDK_15.2.0\examples\iot\mqtt\lwip\subscriber\pca10056\s140\ses\iot_lwip_mqtt_subscriber_pca10056_s140
nRF5_SDK_15...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hi,
I am trying to use UART interface on a nRF9160DK board to connect a rs-232 to rs-485 module for the purpose to make nRF9160DK a Gateway.
But I have no idea where to...
Hi,
Are there any known Android bugs where Android should not bond, but does? I have tried searching the web without too much success.
My central device is an older Android...
Hi,
Is it possible to add scan response with extended advertisement packet?
When I try to add scan response, then I got error NRF_ERROR_INVALID_PARAM.
I am using a nRF52840...
Hi there,
I am using two nRF52 one as Master and the other as Slave SPI, but I am facing an issue with the slave side, because when I use NRF_DRV_SPI_FREQ_125K it get some...
Hi,
I am using the nRF52840 on a custom board with SDK15.2.0 with SD S140 6.1.1.
My current BLE connection parameters are below which allow connection to the nRF Connect...
With Mesh SDK 3.0.0 , i have tested with light switch example with one client and one server, it works. My question is is it possible that one server can communicate to another...
Hello,
I have developed simple scanner application that scans for beacons (apple, nordic and of own type). It prints data about beacons over UART. I have installation where...
Hi,
due to some evaluation effort of nRF52840 Dongle, I went through whole Zephyr project building of their Bluetooth hci_uart example. After couple of ardous hours(or more...
Hi there,
To do LESC with some peripherals supporting OOB Rx, and some not, and the central supporting OOB Tx, I was wondering how to correctly enforce the OOB for the right...
Hello,
I am beginner with NRF 52 DK. I am trying to change the uart example using NRF 52 with SDK 15.02, so that I would send message after pressing button to my PC via...
A temperature and humidity acquisition device uses NRF52832, watchdog, RTC timer, external touch button interruption, BLE open state, feeding the dog every minute through...
Hi,
I am having 2 nRF52 DK boards and I have to blink the leds of one nRF board with the help of another nRF 52 DK buttons and vice versa .
How to do it?
