When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi all,
I have a nrf52832 board from holyiot ( https://pl.aliexpress.com/store/product/Nordic-nRF52832-module-Bluetooth-low-energy-development-board-for-BLE-mesh/420533_32867403706...
Hi,
I'm trying to use an existing NRF51822 mbed codebase on a new NRF52832 product and am having some issues.
First of all, it seems that I can't use mbedlib, but need...
Hi all,
I have a Gateway with nrf52832 BLE chip-set.
My question is: Does this chip-set provide the ability to get the RSSI levels of the three advertisement channels...
At the bottom of page 15 in nRF52832 Product Specification v1.4 the following reference is printed:
[1] See GPIO located near the radio on page 17 for more information....
Hi,
If event is not handled (or handled but EVENT register not cleared), will it go above 1 or is it binary?
In other words, can the value be used to detected missed...
I am attempting to port code from sdk 11 to 15. Some of the code is __older__ and in need of updating. A line which runs during the application init calls the sd_ble_version_get...
Hi!
I have added programs for register writing to SPI programs and using SDK14.0.0
I am using the nrf_drv_spi_transfer function to transfer three data.
but when confirming...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi!!
I am now using SDK 14.0.0. and I have added UART functionality to the SPI program().
I could confirmed that SPI and UART can transmit data separately.
However,...
Hello,
I am trying to modify the ble_app_uart code so that my peripheral can send data automatically to the central, which in turn can print it on a computer through UART...
My application is a BLE peripheral and will only allow a single connection to a BLE central. Hardware will be nRF52832. My test application was based on a Nordic example that...
Hello,
I am working on Bluetooth Mesh authentication. I wonder if you have more details about Input OOB . I am trying to input a number from nRF Mesh app to send it to the...
