Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hello,
I have a problem with turning on notification on a characteristic so I can start receiving data.
I am using a nRf51 dongle as a client device, using softdevice...
Hi, I would like to establish services with following security permissions in a Bluetooth 5 peripheral: Currently I use the NRF52-DK and SDK 15.2 Service A: Security level...
I'm trying to adapt the secure_bootloader example for our custom board with a nRF52832 QFAB with 32kB RAM and 256kB Flash, following the information in this thread:
https...
I'm building a project on top of cli examples:
<SDK>\examples\peripheral\cli
<SDK>\examples\ble_central_and_peripheral\experimental\ble_app_interactive
My goal is...
Hello
I need to setup the the PWM peripheral@ 8MHz with one selectet Channel in DMA mode. For development, I am using the NRF52840 Preview Dev Kit PCA10056 (Q1AAAA). I did...
I have one question, if Nordic can give some confirmation, that Nordic chips can be used together
with Murata XRCGB32M000F1H00R0.
Customer just asks for that I don’t...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
I'm use the app_button lib to deal with button event ,things go well, I assign the push ,release and long push event to button event .
But there came a situation,while the...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
The power estimation tool on https://devzone.nordicsemi.com/power/ maxes out at a minimum interval of 7.5ms and a maximum payload of 27 bytes, with 824mA average current....
