Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
software: ncs 2.5.0, zephyr/samples/subsys/fs/fs_sample
hardware: nRF52840 (not DK, designed by customer) and nRF52832 (not DK, designed by customer)
Step1: build within...
Hello everyone
I'm trying to build an app using Segger Embedded Studio and a nRF52832. I'm currently struggling to include the fds module since i get the following errors...
Hello,
We would like to program the external flash connected to the nRF5340 via SWD during manufacturing.
Is this possible? Do you have any documentation that explains...
Hi
When doing a Software reset the RAM contents are persisted, however when doing a Hardware reset via nREST pin on the module then the non-initialized RAM section is...
Hi,
I am designing the ARGO module http://wizcube.eu/argo.html . I am using the excellent KiCAD library https://github.com/hlord2000/nordic-lib-kicad
It seems there is...
Hi, I'm developing a product for a client using nrf52840 which has support for DFU OTA over BLE. I'm using nrf connect sdk 2.5.0 and DFU OTA over BLE was ridiculously easy...
We're using a nRF5340 module on our board, and have basically everything working as we'd like using SDK 2.1.0.
I've tried updating to SDK 2.6.1, and managed to resolve all...
Hi,
In our new project, we are using the nRF5340 WLCSP package and configuring the system ON - low-power mode in our application code. We measured the current consumption...
Hi,
Ubuntu 20.3
vscode + nrf connect extension
when i create new application from exsample project broadcast_audio_source for nrf5340, after build, and flash into the...
Product: NRF9160
SDK: 2.6.1
Modem: 1.3.6 My problem is that FOTA download is breaking up more or less every time our device is doing a SW upgrade. We download SW directly...
NCS version : v2.6.1
target board: nrf5340dk_nrf5340_cpuapp_ns
sample project: "ncs\v2.6.1\zephyr\samples\application_development\sysbuild\with_mcuboot"
I use this command...
app and dfu works after I program the merged hex from bootloader_setting, bootloader, softdevice, app using Program application tab, but if I erase chip, reprogram it with...
Hello,
Because i want to connect more than two headset to one gateway, so i modify the prj.conf as follow
CONFIG_AUDIO_DEV =2
CONFIG_BT_MAX_CONN =4
CONFIG_BT_MAX_PAIRED...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
