I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
Chip: nRF52840
OS: nRF Connect / Zephyr: v2.3.0
Problem: Saving coredumps to external flash
We're trying to add a bunch of debugging features to our firmware before...
I am using the PCA10040 nRF52DK board
I want to connect the UART RX and TX pins of the nRF52832 to my target CPU
I have cut the connections at SB16 and SB14
I can see...
Hi Sir,
As we know, Matter 1.3 supports Electric Vehicle Charging.
Do we have any plan to support the example of Electric Vehicle Charging?
If yes, what is the time...
Hi, We are using a Segger JLINK to program a nrf5340 product using the SWD interface. We have been successfully programming units using a design where there is a 100k pullup...
When we try to test the stability of the UARTE peripheral, we find that when inserting and removing the RX pin, the uarte_handler callback function is very likely to goes...
What is the recommended UART SUSPEND sequence to use the PM_DEVICE_RUNTIME? I am having trouble using the PM capabilities with the UARTe driver. I am developing on the 52833...
Hi,
I am trying the https://github.com/NordicDeveloperAcademy/bt-fund blefund_less1_exer1 using nRF52840 DK. I am able to connect but not able to detect button press. I...
SDK:17.1
application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble I want to know what operations will be performed when...
Hello,
I saw in an old forum thread ( https://devzone.nordicsemi.com/f/nordic-q-a/79412/lwm2m-amount-of-object-instances-limited ) that block transfer was not fully supported...
Hello! I am using nRF52DK and the nRF Connect SDK with Zephyr to create my custom application. For one part, I am recording IMU values at a frequency of up to 200 Hz and loading...
I am trying to run Gazell libraries on nRF5340. There have been some previous posts about this with answers either saying that the support does not exist, might be coming...
Hello,
I have Micromod nRF52840 module on a carrier board and I've built and flashed Matter Light Switch sample on it but I need to read the logs from the module
How can...
I have a doubt about the BLE callbacks running priority in a thread context. For example, when I define the bt_gatt_notify_func_t callback for the incoming notification, what...
Hi,
I am looking for Bluetooth Broadcaster example program that can run on nRF7002 DK. I am also looking for Bluetooth Observer example program that can run on nRF52840...
