Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
Trying out Nrf5 sdk v17.1 with SES 6.32 and opened up an ANT+ example `ant\ant_debug\d52\s212\ses`
Tried to build, 50% compiled successfully, but i get repeated errors on...
We use nrf52833, and the SDK is 17.1.0. We have the following questions about gzll: 1. How to count packets_num and timeouts_num in Packets Statistics? timeouts_num Where...
Hello,
I am trying to send a large file through BLE from an nRF52811 to a Raspberry Pi 4. File size is about 77 kilobytes.
Here is BLE setup on the nRF side:
Custom...
Using the DM, in the discovery_complete callback, after finding two CCC handles from 2 custom UUID's, I can subscribe to only one of the two, the other fails with EALREADY...
Hi,
I am not sure where to go next, so looking for some debug help.
Setup : I am using the 9160DK - the 52840 is being used as an ANT+ receiver, where it forwards on UARTE...
