Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I would appreciate your feedback on the 802.15.4 CCA implementation on NRF52840.
1. Is it possible to perform CCA without disrupting the RF reception?
2. If it is possible...
Hi,
I use VScode to run my nrf applications. I user nrf52840DK and want to run basic examples 'sensorclient' and 'sensorserver' examples.
The below error shows when I...
Hi,
If we take BLE 4.2 for example, maximum practical throughput is around 100kBps. Does this mean that I can update a service characteristic every 10usec?
Thank you
Hi, I am very new to matter and I would like to query some doubts I had regarding the communication between the chip controller and OTBR.
What protocol is used? I know...
Hello
the nRFConnect v2.0.0. is installed, however, apparently not properly, for example I cannot run the emStudio in ToolchainManger... have a look at the picture, where...
I use SKD 17.1.0, pca10100 and nRF52833.
When I execute "make -j all" at "armgcc" folder" in the terminal. I get the following errors:
This is my project folder.
I...
Good day,
I did follow the usual steps of this an exercise, namely:
1. I did download the base exercise project contained in the zip file: fund_less5_exer1.zip (I attach...
Hi,
I am trying to add OTA DFU functionality to our project using 1-stage MCUBoot. It works fine when I use the default key, I can update OTA firmware. To add a custom key...
Hello,
I am using the Android DFU library . The constructor for the DfuServiceInitiator class accepts a device address. Can one assume that providing an application address...
Hi,
I use sdk153.IC is nrf52840.
Install NRF connect on Android phones such as Samsung vivo oppo. Only Samsung can quickly scan the broadcast and the connection is normal...
Hi Nordic,
I am using your QSPI example code and make it into functions for my application. The code could run if I block the rest part of my code and only run the QSPI...
Hi,
4 years ago we implemented a 802.15.4 and Bluetooth Multi protocol project on the nrf52840. Our application continuously ran 802.15.4 and bluetooth was just used for...
i tried to use the high voltage mode of nrf52840, but when i flash a firmware called "ble_app_hids_keyboard" which use the nrf52 sdk, all is good. but when i flash the firmware...
Hi,
I'm using nRF9160dk to configure MQTT . i'm new to MQTT so ,Is their any example code to understand and work on it by using " ZEPHYR RTOS "
thanks in advance.
A product I'm working on uses an nRF5340 (actually a Fanstel BT40 module with an nRF5340 in it) with NCS v1.7.1.
It's got an SPI slave connection (the nRF is the slave)...
