I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
We have defined a FOTA update for a set of devices. Our device SW follows the 'multi-service sample' code for FOTA.
Generally, FOTA works well for devices in a job...
Currently (as far as i can tell) the firmware for the DECT-NR+ mode is mutually exclusive with the LTE firmware, and you cannot mix the two wireless modes as you have to flash...
We use the device shadow "desired" section to send configuration params to the device. The device processes and accepts the params and then returns them in the "reported"...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
My SPI slave sensor requires a 32-bit frame length. The CS (Chip Select) signal needs to be switched for each 32-bit frame interval, and it also supports DMA (Direct Memory...
Hi ,
I am using skb501 module and which contains nrf52840.I am using nrf5sdk for development for zigbee coordinator because nrf connect sdk is not supportable in this...
Hello!
We are developing a device based on the nRF5340 and using SDK v2.6.0. The firmware implements a USB composite device (CDC ACM + MIDI + Audio). Everything works perfectly...
I am attempting to interface a tas2110 with an nrf52840. I just became aware of some nrf52 limitations and wanted to get the latest info. My requirements are as follows "The...
as shown in this document:
https://www.bluetooth.com/wp-content/uploads/Files/Specification/HTML/Core-54/out/en/host/attribute-protocol--att-.html and Zephyr's att.h , 0x0d...
When I run the peripheral_hids_mouse sample, I scan/connect on nrf connect and see an instance of the peripheral. then if I clear and scan again in the Discovered devices...
