I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I received my NRF52840-DK board, today, from Digi-key. I followed directions in starting it up - power set to USB, switch to on. When I turn it on, all LEDs flash and pressing...
After a lot of stumbling around (the documentation for the ANT+ examples needs to be improved) I finally got some of the ANT+ examples working on my nRF52 DK board. When programmed...
HI
How can I to send 512 characters over BLE NUS?
I saw in Ble uart example this
I received 247data from BLE NUS
can I to receive 512?
how can I do that?
...
Hi,
We are currently going through the Verizon self certify program, using an adaptation of the asset_tracker_v2 firmware on our device. Verizon said to reach out to Nordic...
Look like a hard coded bug in API generated in build\zephyr\include\generated\syscalls\flash.h ?
-- Found BOARD.dts: zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840...
Hello! I have a serial device (RN8209 power meter) which is connected by UART to a nRF52832 with 4800 Baud. I am using SDK17 nrfx UARTE to access it, but I have observed,...
We have a custom board with a uBlox Nina-B1 module. Pin 0.05 is connected to an analog switch (NX3DV2567) which powers a microphone and capacitive switch. When the pin is...
Hi everyone,
I am using nrfConnect 3.9.3, And SDK v1.7.0.
I am working on a project based on uart example.
My question is if there are some way for clean/discard all...
I'm unable to get a cloud response using the XPING command with some IoT sim cards on the nRF9160. I've been working with serial_lte_modem projects on this chipset. I've also...
I cannot find any information on how to update mcuboot over SMP when using the immutable bootloader.
I have my NRF52840 setup with the chained bootloader: b0 -> mcuboot...
Hi,
First of all thank you for your support and suggestions.
As I am planning to use nRF52840 SoC in my design, (Project: BLE based Environmental sensor). The circuit...
Hey. In production we are logging PM error events to try to determine the root cause for some unstable connection that keep showing up. We are seeing with high occurrence...
Hi,
We just received brand new nRF5340DK. By plugging in the USB and putting switch to ON I see the LEDs are blinking, but Windows doesn't detect the DK. We've tried several...
I have looked at other reports on this issue the most thorough one being
https://devzone.nordicsemi.com/f/nordic-q-a/65624/nrf52840-dk-implementing-board-button-event-handler...
