I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi,
When the NRF9160 boots the GPIO level of a given pin, such as P12, is set to high (3.3V) before the main application gets a chance to call gpio_pin_configure and gpio_pin_set...
I am now using the DFU functionality to upgrade the code combined with the CoProcessor and radio_test samples and find that the code takes up too much space to upgrade. I...
I recently bought Thingy:91 (nrf 9160) there was a SIM card included but it didn't work! I have written to support twice at the recommended address [email protected]. it was...
Hello,
I am using PCA10040 DK for the programming with ble_app_beacon_pca10040_s132 example code. I want to broadcast my 20 bytes of data with my 0xFFE0 UUID.
In this...
Hello,
I am using the nrf52840dk_nrf52840 with NCS v1.7.0. I am trying to use the external memory (MX25R64) to host the mcuboot_secondary slot. Then, the primary slot...
Hi, I have recently acquire an nrf52840 development board to prototype a usbd msc. With the example provided in sdk17.02-USBD_MSC, for saving every 1000 frames of data, 100...
Hi
I want to konw what will softdevice or ble do after the chip enters system on mode.How do I know which components are working during advertise and connection intervals...
I am using the MDBT50Q-1MV2 which has the nRF52840, and have burned the Adafruit Feather Express bootloader using a J-link and the Arduino IDE. The issue is that I have not...
Dear, I need to upload data to w website using nRF5340DK. I decided to use NodeMCU V3, which has ESP8266. The related queires are:
1. How to include and use esp8266 shiled...
Hello !
I'm using USB CDC ACM serial port in interrupt driven mode.
I can see driver operate by 64 bytes chunks.
Linux PC is used as data source and I can see 450KB...
Hello, I am fairly new to programing with nRF52832, Segger Embedded Studio and SDK52 V17.0.2.
I am an EE student, and the majorly of my experience comes from Arduino.
...
Hello,
My setup:
nRF5833 DK, OpenOCD-0.11.0 on Windows 10
I installed the xpac OpenOCD package and attepmted to connect to server using the command
and I get the...
I am using the GNSS Sample in SDK 1.8.99 to test sleep/wake cycles.
The GNSS example is correctly operating in single shot mode by setting the interval to 0. After getting...
Hello, I have the custom design. Schematic is below: I use Visual Studio Code and nRF Connect SDK V1.6.1. My programer is NRF52833DK I used example code (zephyr/samples/basic...
Hi,
We used the nrf52840 in our first release of our project. And we decided to upgrade to the NRF5340. We already have port our software to the Zephyr OS on the nrf52840...
