Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
Hi,
I am compiling micropython port for Thingy:52. I am following instructions here https://github.com/micropython/micropython/blob/master/ports/nrf/README.md
I see that...
Hi,
I have created an HSL model and it's working fine. Now, I am using a light that has both CCT and RGB control. So, I have both HSL and CTL model existing in the same...
Board ：52840dk_52840
SDK： NCS1.7.1
IDE ：Visual Studio Code
I remap my bootloader partition in my application .overlay file
as
& boot_partition {
reg = < 0x000000000...
Hi,
When i changed NRF_LOG_ENABLED from 0 to 1 in file sdk_config.h returns the following error
1> Linking tdoa_tag.elf 1> E:/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj...
Hello, did you test the working of 100 pairs (Transmitter and Receiver) nrf52840 BLE modules together indoors? If you did, how much data is lost while working together? Can...
Hi everyone,
I use the radio example as my basis. I call the read_packet() function from receiver example. And there is no incoming data, it stucks there. How can i set...
Hey,
I have an app based on the UART central example. I successfully connect and bond to an android and am able to send data via uart over BLE.
I want to send data also...
Hi
I am converting libraries MAX30105 Arduino to nRF52840, but I have a problem,
"MAX30105 parrticleSensor;" what is it?, how can I to convert this? is it a variable?...
Hello , I am trying to build the bootloader source code provided by Adafruit for its nRF52 core. The project is based in Segger Embedded Studio.
Adafruit's nRF52 core bootloader...
Hi,
1. I removed RTT related codes in the project.
2. Will uncontrollable factors be introduced?
3. Is there any potential risk when the code runs?
Thank you for all...
Hello,
Trying to run the TWI_SCANNER example on a pca10100 hard faults. The .emProject file has been modified per the instructions at https://devzone.nordicsemi.com/f/nordic...
Hi,
I am using nCS to write applications on vscode IDE, that is I am using the "nRF Connect Extension on vscode IDE" I need to unit test the written application code,...
