Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi!
I just wanted to try out the online power profiler. It seems like it is currently not available.
Is this the correct link still https://devzone.nordicsemi.com/nordic...
Hi
testing with thingy91 v1.4.0, firmware 1.5.1.
I never succeeded to enable passive mode of nrf_asset_tracker_v2 no acceleration is detected.
Someone experience the...
Hi,
I'm new to use nrf52832, just as I said above, I want to know if the version of softdevice support bluetooth 5?
Where can I know these information?
Hello,
I've recently been porting a program over to Zephyr and hoping someone here might be able to shed some insight on this issue.
I can't seem to get flash_write to...
Hello,
I want to test a peripheral that uses private address resolution. I would like to set nrf52 eval board used by the nrf Connect Desktop to use a fixed, private random...
Dear Nordic engineers
I recently encountered a problem while developing the program of nRF52833.My program is developed on the basis of nRF5SDK 16.0, using S140 softdevice...
Hi, We recently made a custom board for a new project, based on the nRF52832-QFAA. Everything looked fine in the first place as the nRF is perfectly recognized on a PC and...
On the Eval board layout, the 2 nd and 3 rd layer cut away under the RF trace. That make the substract height equal to 57.87 mil.
For 30 mil width trace, the impedance will...
Dear Nordic support,
i'm evaluating the Nordic nRF52840_Dongle with the SDK 1.5.1, inlucing Zephyr etc. I could successfully compile and load the Blinky-example (..\ncs...
Online orkunsengur 2 days ago
Hi,
When I create and open an project, and I can go project options-->preprocessor-->include directories etc. However, if I use example...
Hiya!
I am writing code to add support for USB on the NRF58233/58240 to MakeCode. MakeCode relies upon WebUSB. At any point, a user can close the website which causes...
I noticed the minimal b0 immutable bootloader build does not fit anymore.
I used the example here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
Hello,
We are using NRF52832 to design a loss preventer product ,can you help to review the design SCH and PCB layout before PCBA making ? main including RF desing , GPIO...
Hi, I was trying to a project that includes edge impulse and nRf5340DK. I successfully run the example project t they provided and now try to use the library provided by edge...
Trying to do DFU over ZigBee, but nrfutil failes:
Gets this problem constantly. I have check all the examples and everything, doble checked all parameters, but always the...
