I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Dear sirs,
Here we've faced with the issue about logs output, could you please help?
We need to use two CDC_ACM devices on the board: one for shell and printk() output...
Hi!
I'm developing a peripheral device using nrf52840 to communicate with our android developed app. I'm testing the latency between connections of device. the configurations...
Hi, I need to estimate the power usage (so looking for TX and RX duty cycle) for the NRF52 during operation.
We will be connecting to a heart rate strap, and recording...
Hello - our certification lab is using the radio test example in order to perform their testing. They claim that the lowest channel they are able to set within the example...
Hello,
I am using nRF52833, nRF Connect SDK v1.5.0.
In v1.5.0 there is one new example i.e Zigbee NCP. ( Zigbee: NCP — nRF Connect SDK 1.5.0 documentation (nordicsemi...
I'm trying to update the advertising data using sd_ble_gap_adv_data_set function but it's not defined in sofdevice s140 v7.2.0 , it's defined in v5.0.0-3.
Please how can...
I installed NRF connect SDK v1.5.0-rc1.0 through toolchain manager.Open SES and create a project with open NRF connect SDK project.An error occurred.'create_nordic_project...
This function succeeds only when Thread protocols are disabled. my question is: if the Thread protocols are enable,what should I do to disable them ，now what I do is:
"otThreadSetEnabled...
Hi . I am developing nRF52 for the first time. (PCA10056_ nRF52840 _S140_ ver1.70.0 _DK under development..) It is under development with SEGGER embedded studio. I want to...
I'm new to NCS, and playing it with nrf5340 pdk kit.
My problem is ,I can't play any projects, all of them go to the same error: cmake failed,create_nordic_project.py failed...
Hi,
To support the large and dense networks we are building, I need my network coordinator to be able to throttle OTA packets to not completely overtake the network’s bandwidth...
Hi,
I want to create a mesh between my nRF53 DK and dongle. For my project, I created my own service to send accelerometer value to the client (mobile application). Now...
I am developing an application that sends an image with BLE to an android phone. It is remarkable similar to the Image transfer demo ( https://github.com/NordicPlayground...
Hi
I am updating from Softdevice 6.1.1 to 7.2.0 and have issues with nrf_sdh_ble_enable(..), My setup is:
NRF52840
SDK 17.0.2
SoftDevice 7.2.0
Running FreeRtos...
