Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Dear Nordic expert,
I'm using nRF52840 as central with SDK 16.0.0.
I establish a connection with a peripheral (phone) and then I need to drop the connection. I set a timer...
Hi, everyone on the community
When using the BLE_APP_UART example, the serial port sends a packet of data to the mobile phone every 10ms, resulting in the device disconnecting...
I want to have a very stripped down version of the cat-tracker-app that just deals with settings, so I can import what is useful to an existing web application. I am new to...
I have succesfully got extended advertising working using the nRF SDK on the nRF52 DK, however I haven't been able to assign it a 128 bit service guid.
Setup:
The device...
Hi,
I want to add DFU to our board running SDK11 S130 but facing some problems.
I followed the instructions on infocenter, and started with ble_app_hrs example (from here...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
Hi All, I try to run the example GFX in sdk 17.02.
I wired the TFT :
---VCC ------------------ +3V ---GND ------------------ GND ---CS -------------------- P1.09 --...
Hello ,
NRF52840
sdk 15.2
In my application using ble central example in nrf52840 , i am able to write data in led characteristics and getting notification on HVX using...
Hi, I have tried to add support for BOS descriptor by appending a custom class generated from the Dummy example. The "main" class is the HID generic class, but with the NRF...
Hello
I only used PWM_library, but this is my first time using PWM_driver. Simply controlling the duty cycle of multiple channels has been successful, but I am not sure...
A little backgroud for my project. The goal of the project is to be able to identify the proximity of beaconing devices in an area to a specific observer which then reports...
Hi, Below is the mapping of RAM on the 840 from the infocenter. We want to utilize the functionality to turn off unused RAM (via sd_power_ram_power_clr), but we see that if...
I am using SoftDevice s140v6.1.1. The behavior is I was able to program nRF52840 through JTAG without any issue. I am checking out the OTA firmware update feature and nRFConnect...
Hello Everyone,
I am developing one product using nRF52840 MCU, in this project my master controller is nRF52840 MCU and the host is STM-based MCU.
My goal is to make...
Hi,
I am configuring a test software to generate CW signals at channel 0, 19 and 39. Currently I'm using the nRF52840dk, later a custom board. The channel number is calculated...
