I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
In using the Thingy52 I can't figure out how to just get the just XY coordinates from the motion sensor - or any other sensor. I'm trying to figure out if I can capture motion...
hi, i am a student, i am new to nrf52840 DK. I downloaded Gooligmelec "nrf52test-led-battery" from github and open Solution inside SES . it was running ok. when suddenly....
Hello,
I am using nrf52840 and SDK 15.3.0. and the device wakes up every hour and every day for reporting data.
So I am using app timer to wake up also using app_timer...
Hi,
I am working on nrf52840 and using below SDK and softdevice.
SDK - 16.0
Softdevice - S140
IDE - embedded segger studio.
currently using nRF52840-DK.
I am using...
Hi Team,
We are using the Micro ECC functionalities , for that we need the SHA 256 Library,Micro ECC library won't have inbuilt SHA.So how to enable the SHA for Micro...
We are using a nordic 52840 chip with a S140 softdevice as a client to connect with GATT servers from smartphones. When we connect to one of our smartphones, we do get the...
Hi all,
i've try to update the NRF52_DK interface MCU firmware to MBED firmware (nrf5x_atsam3u2c_if_mbed_V0221_11012017.bin).
After power cycle, LD5 at interface MCU...
Any hints on connecting to HID keyboard example from linux command line ??
Running stock ble_app_hids_keyboard/pca10040/s112/ on eval board. Works fine with iPhone but can...
Hi! I'm configuring RTC on nrf51822. I'm setting up the LFCLK and RTC module by configuring their registers. I have set up a simple IRQ handler, but it seems that it never...
Hi,
I have few question on nRF9160 Thingy:91 and Dev Board.
1. From the schematic, I see that have used SP8T Switch from Antenna Feed pin (GPS and LTE) to the SIngle Antenna...
Hi, we want the DFU code in SDK 10.0 for NRF51 S110 to finish faster. The case we are optimizing is when there is dfu ongoing, just a simple boot.
Currently the main time...
