Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
When i start the nRF mesh app, it crashes immediatly. What do i need to do? I re installed it a couple times and i rebooted my phone a couple times.
The phone is a samsung...
Hi,
I am developing firmware both nrf52 and nrf91.
in nrf52, I activated BLE, usb and uart. Uart communication established between nrf52 and nrf91.
in nrf91, I activated...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag). I can able to control led's using customized board. But Bluetooth is...
I am using the gazell protocol of nrf52840,how to use broadcast radio mode from host to device based on the gazell protocol ?or can I use the gazell protocol to make it possible...
We have an neural network running on a 52832 using the floating point unit. We started encountering FPU exceptions so we enabled the FPU IRQ to identify which specific instructions...
Hi everyone,
I want to create multiple USB instances using only one nRF52840 dongle. I want to implement one CDC ACM class instance and another one instance that has two...
Hi,
I have a problem with floating point types on nrf9160.
I get an exception when I get to a simple floating point assinment:
void f(int i)
{
float x;
x = (float...
Hi everyone!
I'm new using Nordic Semiconductor products, I have a Nordic Thingy 91 running Asset Tracker application by default.
I want to test only specific things first...
I was thinking of using the nordic thingy:91 for monitoring purposes in seismic areas.
To this aim, I would need to have some sensors deployed in the environment which:...
Hi,
I need to use nrf_dfu_settings.c to detect external firmware in Bank 1 during application boot. I also need to use Falsh Data Storage to save application parameters...
Hi All,
I'm working from the Thread CLI example, and I got a network of multiple thread devices that works just fine (they see each other, and can send/receive messages...
Hi there,
I'm trying to do a basic test with the GPIO/NMOS - just trying to turn an LED on and off for now. We're going to be doing this in response to the outcome of an...
Hello,
I'm working on the mqtt_simple sample in zephyr environment for NRF9160 board.
We tested the firmware with 2 sim cards with different packets: IPv4 and IPv6,...
