When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
Hi all,
I'm working on a project which I started from the multiperipheral example. I am using SDK 15.3.0 for this. I am developing the software on the nrf52840 DK using...
Start SEGGER Embedded Studio by clicking Open IDE //Successfully installed, what means Open IDE ? ? ?
Select File → Open nRF Connect SDK Project… //it just dont appear in...
Hi,
Currently, I am in a feasibility analysis stage for an application which requires BLE Mesh with Localization (RTLS using AoA and AoD). I explored SDKs for nRF52833...
Hello,
on SDK16, with nrd52dk, with android phone, standard ble_app_uart example works fine with nRF Toolbox. But when I disconnect from nrf52dk, the chip still thinks the...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I changed the device name while not connected.
but, The...
Hello,
I am trying to follow the tutorial SDK UART coexistence example , but it seems like the last step cannot be completed. As you can see, that .hex file does not exist...
I am working on a low power peripheral project (similar to the Nordic blePeripheral/uart example). I'm going to be using an nRF52805 with SDK 17 and s112. I found the Apple...
Dear all,
I have tried my best to find answers in questions posted previously but I still have a few questions that I would like to clear up. I will keep it concise. Thank...
I want to configure the UART1 (not the UART0), and I want to know if there have some examples that introducing the UART configuration by directing accessing the register....
Does Nordic have programming for the nRF52840 that enables both 802.15.4 and BLE, so the board can both become part of an 802.15.4 network and pair with a mobile device like...
Hi All,
i played with the /examples/dfu/secure_bootloader/pca10056_S140_ble_debug.
The application works fine so far.
I do have the following questions.
Is it...
Hi,
I am running into some problems with libuarte. I have two nRF52840-DKs talking to each other over UART. My setup is not ordinary however. The hardware configuration...
