I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
Hello -
We are working with the nRF52840 and SDK v17.0.0 and tuning our power consumption during System ON sleep. We understand how to wakeup the device using the RTC and...
Hi,
I have encounter a problem that the first button release event is missing if the key is pressed while powering up.
The SDK I am using is nRF5_SDK_17.0.0_9d13099. ...
Hi!
We are using nRF52832-QFAB (B0 variant) in one of our projects, and it works fine and well.
We are now in the process of using the nRF52832-QFAB-E0 in the same build...
how can I work it use nRF5 SDK 17.0.0? On https://developer.nordicsemi.com/nRF5_SDK/pieces/nRF_DeviceFamilyPack/ the newest pack is
NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Support Team,
An error occurs when generating a signed binary file for central_dfu_smp.
Error: Header padding was not requested and image does not start with zeros...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
Hello!
I've only used the DK board so far, so I've rarely used an external debugger.
I'm going to use a custom board later, so I'd like to learn more about how to use...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
I use nrf5_SDK_for_Mesh_v420 on four nRF52 DK board, one is client, the other is server. But I fond, the light_switch_client example is used to control two server board, now...
Hello,
I am using the Light switch example for BLE meshing. I am trying to provision the nRF52832 with Raspberry Pi. I am unable to successfully provision because of the...
Hello!
I have created a function that cancels the connection by pressing and holding the button when Bluetooth is connected.
The use of this code allows the connection...
Hello,
I want to use FDS with bootloader but i get this error and i'am not sure how to manage it cleanly:
Linking target: _build/nrf52840_xxaa_s140.out
_build/nrf52840_xxaa_s140...
