When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
I am trying to disable writes to certain regions of flash memory. But different from the nRF52840 Product Specification, NRF_ACL is missing the DISABLEINDEBUG register...
Hello,
I'm trying to connect a bluetooth device (peripheral) with Web Bluetooth (central). I send an addvertising packet and I can see the device in Web Bluetooth but I...
Hi,
I just bought an NRF51-DK which I want to use with MBED. I need to download the CMSIS-DAP firmware for this board but cannot find it on the downloads page for this DK...
Hi,
i am trying to create a new model for mesh SDK 4.2.0 i am using nrf52832 please provide link or any document for creating new model, i found a link which is for SDK...
I have been using the nRF5 Mesh SDK for development and am in need of implementing single press, double press and long press on the nRF52832. I have seen the nRF5 SDK for...
Hi,
I get the error "[DFU] Remote DFU error: INVALID OBJECT. SD busy? Retrying...." when attempting a firmware update over Bluetooth.
The bootloader, application and the...
Hello,
I'm working on nRF52811, SDK16.0, Softdevice 7.0.1.
Using the pwm_driver example in the SDK, I'm trying to run a simple PWM for an RGB LED. Following is my simplified...
Hello,
I am trying to develop a product on a large scale. I need the last 4 digits of DEVICEADDR[0] as the advertising name for uniqueness. But I am not able to get it working...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
Hi,
I'm using saadc library to measure the voltage on nrf52832 DK. also I'm using soft device s132 on the project. I have several questions and will list below,
I want...
Dear Team,
I am trying to use nrf53840 USB dongle as sniffer. getting following error.
Reopen device failed: Timeout while waiting for device FAC66FF88C25 to be attached...
hai ,
In my application to connect 5 peripherals with central and here i am connecting with device names
static char const m_target_periph_name1[] = "Nordic_Blinky1";...
I try to send NRF_DFU_OP_PING reqeust ,then received BLE_GATTC_EVT_WRITE_RSP message. but write_rsp.len is equal to 0,.I can see gatt_status is BLE_GATT_STATUS_SUCCESS. I...
