I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello
my setup is s140, nrf52840. it is flashed the open bootloader(usb-serial) , the softdevice and an application and everything works fine, flashing running and updating...
hello nordic
i am working with nrf52832, with sdk 16.0 and s132 softdevice, tough i belive this question is relevant to all anrf52
i work with the twi driver (for i2c...
Hi every one , i tries to call the generic_onoff_client_set function to send a message from the client to the server but this ain't working. Can someone please help me?
...
Dear Forum,
I am looking for an OAM vendor offering a small keypad / pinpad device running on an nRF52 SoC. Should be powered by a rechargeable battery and have mini USB...
Hello.
I want to use the nrf52840 as Bluetooth radio controller which is connected over UART to Linux based ARM host.
We are targetting to use meshctl on linux host...
Hi ,
We are facing a problem with cellular connection in NB-IOT mode on NRF9160. We are trying with the asset tracker sample , but cellular connection does not happen. Can...
Hello Everyone,
I started to use the NRF52832 recently and wanted to use it with a sensor from Melexis called MLX90632. I am using sdk 15.0.0.
This sensor have a library...
Hello,
Currently I would like to add a functionality to Bluetooth Low Energy App (BLE). I have a bluetooth slave device that require a specific sequence of sending string...
So, i have been trying to perform a DFU over serial using the method mentioned here by Hung Bui.
Here is a summary of what i did:
- build and flash mcuboot
- build and...
I am using pc-nrfutil to perform FW upgrade (transport is serial), The target is custom board with 52840 processor, running Bootloader adapted from the SDK.
For most of...
I've configured the SPI with DMA module as in the code below.
I've loaded the tx buffer with sample data and start the transaction; however, I'm not reading anything either...
Hello,
I have been working on porting the BLE UART PHY S erialization to the STM32L476 (with a Nordic NRF52832 Dev Board and STM32L476 Nucleo-64). I have read the porting...
Dear Nordic,
Running BLE mesh sensor network with multiple servers and a single client linked to a gateway.
SDK: 16.0.0_98a08e2
SDK Mesh: v4.0.0
nRF52840
The client...
I'm attempting to using pa_lna_setup(), specifically the softdevice function sd_ble_opt_set to enable/disable the radio and an external amplifier. My application is a custom...
Hi Team,
We are using the uECC library for ECC Functionalities, while connecting the debugger we are getting the pop up message like "not finding the source file".But while...
