I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello,
I use the LAIRD module BL652 with an nRF52832 with the SoftDevice 14.0.0 (old version…).
The application use the BLE with the SoftDevice.
We have mesured the...
Hello,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
For my Application,i need to go with DFU.so i merged my application into the example code of DFU...
Hello,
Does anyone know if the FreeRTOS port that's distributed with the nRF5_SDK_14.2.0 is intended to support nRF52810 chips (which have no hardware FPU)? I started working...
SDK 14.2 keil5
I want to run freertos with nrf52810.but I did not find any example .
Is there anyone have tried this?
I downloaded nrf52832 code(ble_app_hrs_freertos...
Hello All,
I have looked around for answers to my specific issue, however I did not seem to find one that aided me enough to fix my issue.
I have created a BLE profile...
Hello,
SDK 15.2, SD 6.1.0 with PCA10056 1.0.0, 2018.20. nRF Connect App v4.22.3. Pixel XL.
I'm running into an issue with my application where the phone disconnects after...
Using: Linux (Ubuntu 18.04), gcc/Eclipse, nrf52840, v15.3.0 SDK, SD 6.1.1
It has been a real bear of time using the SDFU in the newest version of the SDK. There were a lot...
Dear support,
Our team is considered doing their own smart watch, so i found that nRF52 chip is a nice solution. Just before we start, i would like to do some basic questions...
When we ported our FreeRTOS based project to SDK 15.3 from 15.2, we noticed a big jump in the CPU Usage. It turned out that the issue was in SDK 15.3's freertos port_cmsis_systick...
Hi nordic,
I send multiple bytes but always only receive packets of length = 1. For example in the picture, I sent 2 bytes 0x68, 0x69 ('DE') but only received the first...
