Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I've noticed sometimes the merged hex file differs slightly between different mergehex runs when merging the same hex files. Is this a bug or mergehex tool never guarantees...
Hello!
I'm having a problem and a hard time trying to understand what's wrong. Currently, I'm using the SDK 14.2.0, SD 5.0.0 and Segger on macOS 10.14.2.
I'm using the...
Hello,
I have a product using NUS profile and plan to update it to support connection from multiple phone
Do you recommend to start from Multiperipheral example and...
if i use this code to send data,i sometimes miss data..
do { err_code = ble_nus_string_send(&m_nus, (uint8_t*)data, &data_len); if (( err_code != NRF_ERROR_INVALID_STATE...
I have nrfutil version 5.0.0. I run this command:
nrfutil pkg generate --hw-version 52 --sd-req 0xA8,0xAF,0xB7 --application-version 2 --application ./nrf5/Debug/nrf5.ihex...
Hello! We are trying to use Nordic AndroidScannerCompatLibrary in our Android application to scan BLE devices and measure its RSSI level. BLE devices is mounted on ceiling...
Hello there,
I would like to read the data I sent through a WS2812b LED string. I drove it using I2S. Upon reading it, seems like it is not a good idea to read it using...
Not sure what I did to cause this, but my nRF52840 no longer works. I searched for solutions and came across:
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52...
Hi,
I am wandering if it would be possible at all, to wrap a quarter wave antenna printed on flex pcb around a cylindrical battery (LiFePo4)?
Would the radiation be...
Hello,
Information:
SEGGER Embedded studio Studio v412
Windows 10
nRF52832 on a development board.
We are attempting to merge an application with a bootloader...
I have read that the nrf51822 is not supported anymore in the examples of SDK's older then V12.
Does the nrf51 completly not work anymore with newer SDK's or are only the...
I have my system working with softdevice compiled in but not enabled. System communicates with external chip using SPIM peripheral, everything is working fine until I enable...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
