Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
For nRF52840 (Rigado BMD-340), SDK 15.0.0, custom board:
I'm trying to implement nrfx_uart directly to communicate to another microcontroller. I've configured it for blocking...
Hi all
I'm using the NFCT peripheral of the nRF52832 Revision 1 and I'm facing the following issue:
When the reader sends the SLP_REQ, the NFCT receives an incomplete...
Hi, there
I want to remove the bond in current time service example, because the bond process make me less convenient when I debug. so I changed the code in peer_manager_init...
Hi using dev kit pca10040 and sdk 14.2.
I'm trying to use the dev kit buttons to stub out an ANT+ bike speed sensor. Essentially I just need a way to provide a speed reading...
Hello, i am using ble_app_uart example. i am trying to send A to Z from ble to uart. Has i noticed, it is transferring 20 characters at a time. to make sure that i add print...
I am using nRF5_SDK_15.2.0_9412b96. I have application data that accumulate in flash but can be thrown away before re-flashing new app image. I am thinking about instead of...
Hi,
I configured nrf_ble_qwr to use 256 byte long buffer in my BLE peripheral. I registered my value handles (2) which I want to support long writes using nrf_ble_qwr_attr_register...
Hi Folks,
I'm new at using the nRF52832 chip. I recently was handed a 3rd party board to evaluate and up until today I was able to use the nRF52 Development Kit to act...
Hi,
I am working on "nRf52832 - PC10040" based ISP1507/. I have already adapted the peripheral/spi example of SDK 15.0.0 to my needs. Now, I want to merge this spi example...
Hello,
With Segger ES I am able to compile and run the Blinky example (pca10040, S132) from the nRF5 SDK without any issues, it loads on my nRF52 DK board on and it shows...
Hi,
I'm working on a project where I need to collect and process analog data coming from high speed sensor measurements. The data needs to be read at a speed of 25k samples...
Hi,
I am trying to convert the string from ctime to a struct but i always get garbage values if i use "uint8_t". But i can get correct values if i use "int" datatype....
Hello Nordic
Bluetooth SIG had released their new bluetooth core specification 5.1 with new feature is " Direction Finding ".
I know that all nrf52 now support BLE 5.0...
Hi,
I'm using the NRF52840 PDK version:
PCA10056
0.11.0
2018.3
With SDK version 15.2
I've been trying to develop an application based on the HID Generic example...
