Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have been working on a C++ library for the BME280 sensor to be used within the Nordic SDK and am so far only focused on using TWIM, Within this library I intend to use TWIM...
when i use the ble_adverting_start(BLE_ADV_MODE_FAST);
and then use the ble _advering_start(BLE_ADV_MODE_IDLE);
then ble_adverting_start(BLE_ADV_MODE_FAST); the return err_code...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
I have implemented Legacy OOB on NFC and when my Android phone attempts to pair with the device, I receive a NRF_ERROR_STORAGE_FULL error in PM_EVT_CONN_SEC_FAILED event durring...
Hi, now I'm developing my projects(bt-audio-advertiser) with SDK 15.2. and Thingy:52.
I want to load PDM data to extended advertising packets. I succeeded to use extended...
Hi, now I'm developing my projects with SDK 15.2. and Thingy:52.
The projects are bt-audio-advertiser and bt-audio-receiver.
I adapted extended advertising to a Thingy...
Hi,
I have a problem making NFC (with a simple text record) work when I enable SoftDevice: I do not receive any NFC event and NFC communication does not work.
I have a...
Hello,
I would like to get the value of a temperature sensor, convert it from A -> D, send it to a server and then get it with a client (mobile application)
I need a sensor...
Is there any way to perform multiple DFU simultaneously using the single nRF51 dongle. I have to perform DFU from a custom application developed on windows PC. As I need to...
Hi ,
I am running example in nrf52840 using segger embedded studio .
And i am trying to define __no_init variant ,
May be sameone know what is the syntax . in IAR __no_init...
Hi all,
I am building a demo for Bluetooth mesh networking with thingy. I had followed the instructions under this link:
https://github.com/NordicPlayground/thingy52-mesh...
Hi,
I am using the twi_sensor example in the board PCA10056 with SDK v15.2.0. I am trying to disable the internal pull-up resistors of SDA and SCL lines to use external...
There appears to be a design flaw in the nrf_sdk_freertos code that produces a race condition. The race condition can result in a delay in processing a SoftDevice event, or...
When setting up Heartbeat Subscription for a node, a single unicast address is specified as the source. Does this mean that a node can only subscribe to heartbeat messages...
Hello, I am using nrf52 with sdk 13.0.0. Bootloader_secure_ble gives error while compiling. What should I do ?
Error[Lt009]: Inconsistent wchar_t size
micro_ecc_lib_uECC...
