Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
Do you know when the PWM or the ADC functionality will be added to Zephyr for the nRF52 chips?
Can we use the nRF SDK inside a Zephyr application to use unimplemented...
Hello,
sorry to have to ask again, but from reading through all the posts I could not quite figure out how much current the SPI should draw when it is active and reading...
Hello everyone,
I am looking forward to 3rd party BLE modules in which I am interested in choosing Taiyo Yuden EYSHCNZWZ
I want to know that can we flash our code using...
I am using 3 nrf52 DKs with S132 and SDK14 / and SDK15 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and...
Hi All,
We are working on nRF52810 chip for on of our beacon project and we are using external antenna on board but
We are dealing with the Reason 8 disconnections.
...
Hey Team,
Can anyone please share the layout of the Program and Debug connector on the Thingy? I don't have a 10 pin SWD connector readily available and need to start...
Hi everyone, I have configured the LOG module to use it with the UART in view of debugging. I don't send anything in my loop but the UART send constantly these data :
<info...
Hello,
I am using sdk12.2.2 and nrf52832 customised board. My use case is as follows.
Suppose user enters in dfu mode trough app and for example user doesn't update...
I am working with nRF5_SDK_14.2.0 ble_app_beacon example using NRF52 DK. If I have directly copy pated the readily available examples\ble_peripheral\ble_app_beacon\hex\ble_app_beacon_pca10040_s132...
Hello,
I am building an application that doesn't need high-frequency microphone data.
I want to sample the PDM at 4K. It is possible to do so by changing the frequency...
Hi,
After i merged the light switch example in mesh_v1.0,1 sdk with UART example in nRF5 _v14.2 sdk, i'm trying now to put the status data recieved from server node to UART...
Hi,
We develop two BLE projects on NRF51822 and NRF52832 chips.
In both chips, for higher accuracy (better than ±250ppm) exists the option to connect the LFXO 32kHz crystal...
Dear Nordic Engineer,
I am working on sdk15,52840,ble app uart project,
i saw BLE_DTM_ENABLED in sdk config.
// <q> BLE_DTM_ENABLED - ble_dtm - Module for testing RF...
after flashing the board couple of times I get the following error:
device recognized by PC, I can see the drive created on PC
however I can not flash the device, and...
