Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Good Day,
We have an ongoing project that uses an RP2040 MCU (with FreeRTOS) and we need to add WiFi capabilities to it. It needs to be dual-band and fairly high throughput...
Hi all,
I'm currently working with the nRF52 DK (nRF52832_xxAA_REV3) using the nRF5 SDK version 17.1.0_ddde560 and the IAR Embedded Workbench - Arm 8.32.3 IDE. I'm facing...
Hi Team,
I just want clarity on 2 points related to accuracy of nRF9151 GPS.
1) As shown in datasheet, "Positioning accuracy (CEP50), periodic tracking" is 3.4m. So that...
Description: I am encountering an issue while testing the watchdog functionality. When I intentionally hang the system for longer than the configured watchdog timeout period...
Hello,
I'm new to software development so apologies if this is a simple question but I can't find a straightforward answer for nordic connect sdk on vs code.
An IC I...
How can i configure the nrf52840 dongle with DHT-11 sensor such that i am able to use it to send the temperature data via UDP within the Thread Network? I am using the NRF52840...
Hello, I have used this template (ncs-example-application) to start developing my project. I've installed also all the prerequiries to use the application using command line...
I am using the existing nRF Connect SDK (v2.9.0) example of Wi-Fi provisioning using Bluetooth LE ( https://github.com/nrfconnect/sdk-nrf/tree/main/samples/wifi/provisioning...
Hello,
I am currently testing a custom board using the nRF5340QKAA .
Most of the connections are the same as the nRF5340 DK , but the main difference is that I built the...
I dont have Ellisys, but I already install Ellisys Bluetooth Analyzer on my PC.
I got a .btt file in this ticket , but it seems something wrong.
I want some .btt files...
I am using an nRF52840 processor within a Particle Argon IoT module. I am polling a third party BLE peripheral (Shelly relay) for status data once a minute. The data packet...
when i try to use the ddfs to calculate the distance, i can't understand the comments in the README file,
"Zero-distance calibration
*************************
The...
I have followed the guide at https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu .
(using the option CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
After the Matter device is upgraded from version 1.1 to 1.3 via OTA, the Thread connection is functioning normally., but it fails to process chip-tool commands, and chip-tool...
