Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I believe there is a significant inconsistency between the documentation and implementation of AoA antenna switching in the nRF Connect SDK. My testing of this was done...
I have a custom nRF9160 application running based on asset_tracker_v2. It is working perfectly but I am seeing location error messages. The nRF9160 we have does not have GPS...
Hi everyone! I have a custom board with the Adarfuit UF2 Bootloader ( https://github.com/adafruit/Adafruit_nRF52_Bootloader) and a SoftDevice. With the old SDK v2.5.1 I created...
Hi! So I am trying to control two micro servos, MS18 with the nRF connect app. So far I have the code where I can control it with one instance, and hitting the true false...
I am trying to work with a BLE Mesh network. I am using the nRF5340 as a light and another board, the BGM220, as a switch. Both are provisioned and configured, but the switch...
Hi everyone,
I'm currently trying to build a program with the extension "nRF Connect", and here is how i proceed :
- add build configuration --> nrf5340_audio_dk/nrf5340...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
Hello,
this is the first time I work with this device and the device is not for me or for my company.
I have to do an automatic test application, which should program...
Hi there,
So I am using an adapted version of the echo sample for I2S in the nRF Connect SDK in VS Code. I only want to use the echo example in receiving mode, so I have...
Hi, I'm using the nrf9160 with ncs2.7 on a custom board. Does the APN need to be explicilty set with `CONFIG_MODEM_ CELLULAR_APN` ? Or will it auto detect? Does it depend...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
