hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello! I was building a custom board and tried to build the project for my board but it gives an error: === child image hci_ipc - CPUNET begin === loading initial cache file...
My understanding is that Singled-linked list built in to zephyr... https://docs.zephyrproject.org/latest/kernel/data_structures/slist.html But, I don't quite understand how...
Hey I've got this project that requires two buttons. In normal mode, these buttons react to the Ready pin switch signals. when it goes into sleep mode (where it controls other...
I am using ESB communication.
In general situations, data transmission works well. However, issues arise when multiple PTX devices transmit simultaneously.
It's understandable...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
So I was experimenting with the Hardware Codec and I created a simple config which redirects the audio coming from the LINE IN mic to HEADPHONE OUT speakers.
Here's the...
We used the ADC nrf52832 to collect the reference source voltage, 1.240V. It is found that the consistency of each power-on is not good, for example, sometimes it is 2806...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When testing the power consumption of the product with main IC 52832, we found that under the condition of 0dBm 1000ms, the peak current of beacon with PPK2 is about 15mA...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
