Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone, currently I am writing a program to read the SCD41(I2C) sensor and then use BLE to transmit information. With a separate program in twi_sensor, I see that...
Hello nRF team. Is there any different bewteen passing AT command and directly calling the Modem lbraries APIs(from nRF Connect SDK v2.5.2) to control the modem? For example...
Currently our product shipped with SD132 7.0.1, and bootloader/dfu compiled with SDK 16.0.0
We are testing update the bootloader on production devices, and want know how...
Hi Team, I am trying to do DTM test in NRF 52840 using Zephyr- os .The DTM code is working fine on my dev kit ( NRF 52832).I compiled DTM code for NRF 52840 and changed the...
Hi,
I have a problem with sending over NB-IoT to a cloud service. I have found that the helt of my messages only arrive in the AWS cloud and it seems like the modem also...
Hi Support Team
We use ncs to develop nRF52840 application and want to know how many low power mode do ncs have and how to enter these low power mode.We want the nRF52840...
Hello,
We are searching for a board that supports Angle of Arrival(AOA) and Angle of Departure (AOD) for conducted mode radio testing.We need a board euipped with an antenna...
Dear Nordic team
I have the following code for testing the SPIM function of nRF52832.
NRF_SPIM1->EVENTS_END = 0U; NRF_SPIM1->ENABLE = 0; NRF_SPIM1->ENABLE = (SPIM_ENABLE_ENABLE_Enabled...
Hi Nordic .
We are developing an application with nRF5340. In this application, we need to use the SPI Slave feature. According to the documentation, there isn't a clear...
Hi everybody I'm using sample bluetooth peripheral with sdk v2.6.1 and toolchain v2.6.1 to load with nrf5340 but it doesn't seem to build, I see the library has changed from...
Hi,
I am looking into adding BLE OTA firmware update functionality and started by exploring the example provided in Nordic SDK (SDK v16.0.0) while following the documentation...
i'm trying to get an interrupt using sensor lis2dw12 , i have connected my int1 pin of sensor to my gpio 0.10. whenever data is ready it should give me an interrupt this is...
hello Nordic
i am working with ncs v2.5.0 (with nrf52840 and nrf52832)
i am using the fs_mgmt.c for upload/download files from lfs.
till now used it only on one side...
I have connected BLE device to the Nordic's power profiler kit 2 to do power analysis.
My BLE device advertises every 5 seconds.
I can see current consumption spike every...
